heating
No Heat? What to Check Before You Call
If your furnace isn’t making any heat, check the thermostat, the furnace switch and breaker, the panel door, the filter and the gas valve before you call, because plenty of no-heat problems turn out to be a setting or a switch. If you smell gas, hear a carbon monoxide alarm, or still have no heat after the checks, stop there and get help.
A cold snap is when a furnace that coasted through mild fall days has to run for hours at a stretch, and that’s when small problems show up. In St. Charles County homes built from the 1970s to the 2000s, that furnace is often 10 to 20 years old. Here’s what you can safely check yourself, in the order we’d check it.
If the blower runs but the air is cold, that’s a different problem, covered in our post on why a furnace blows cold air.
Is the thermostat actually calling for heat?
After a summer of air conditioning, this is the easiest thing to miss.
- Make sure it’s set to HEAT, not COOL or OFF.
- Set the temperature a few degrees above what the room is now. If it’s set to 68 and the house is 69, the furnace has no reason to start.
- If the screen is blank or faint, replace the batteries. Dead batteries can stop a thermostat calling for heat.
- Check the schedule. A programmable or smart thermostat may be holding the house cooler at night or while you’re out. Use the hold setting to test it, and turn off any away or eco mode.
Then give it a minute or two. Most furnaces run a short start-up sequence before warm air reaches the vents.
Is the furnace getting power?
- The furnace switch. It looks like a light switch and usually sits on or near the furnace, or at the top of the basement stairs. It’s easy to flip off by mistake when you’re reaching for the light.
- The breaker. Look in your electrical panel for one marked furnace or HVAC. A tripped breaker often sits between on and off. Push it fully off, then back on, once.
- If it trips again, leave it off. Resetting a breaker over and over isn’t safe.
Is the panel door closed and the filter clear?
- The panel door. Most furnaces have a safety switch that cuts the power when the front panel is off. If the filter was changed recently or the panel got knocked, press it back so it sits flat and secure.
- The filter. A clogged filter starves the furnace of air, the furnace overheats, and a safety control called a limit switch shuts the burners off. That can look like heat that runs a few minutes and quits, or no heat at all. Hold the filter up to a light. If you can’t see light through it, replace it with the arrow pointing toward the furnace. Our heating maintenance page covers what else a yearly visit keeps clean.
Is the gas on, and is the pilot lit?
- The gas valve. Follow the gas pipe to the furnace and find the shutoff handle. In line with the pipe means open. Crossways means closed. If you know why it was turned off, open it. If you don’t, leave it and call. If your gas stove or water heater is out too, call your gas company. The problem may be the supply to the house.
- The propane tank, if you have one. Check the gauge. An empty tank looks just like a broken furnace, and the fix is a call to your propane supplier.
- The pilot, on older furnaces only. A furnace that’s 10 to 20 years old almost certainly lights itself electronically, so there’s nothing to light by hand. If yours is older, with a small flame visible through a little window, check that it’s lit. If it’s out, follow the lighting instructions on the label inside the furnace exactly, including the wait before relighting. If it won’t stay lit, call. Never relight anything if you smell gas.
What if there’s water, a blocked vent or a blinking light?
- Water around a high-efficiency furnace. If your furnace vents through white plastic pipes, it makes water as it runs, and that water drains through a small tube, often to a little pump. If the drain clogs or the pump fails, a float switch shuts the furnace down. Check that the pump is plugged in. Standing water or a full pump means you’ve likely found the problem, and that’s a good point to call.
- A blocked vent. Those white pipes end outside, usually on a side wall. Snow, leaves or a nest over the opening can shut the furnace down. If you can reach them from the ground, clear them by hand. Don’t climb a ladder or go on the roof to do it.
- A blinking status light. Most modern furnaces have a small light, visible through a window in the lower panel, that blinks a code when something’s wrong. Count the blinks before you open anything, because removing the panel cuts the power and can clear the code. Then check the code chart on the panel label and write down what it says. Give the technician the count. It helps them find the problem faster.
When should you stop checking and call?
These are the points where DIY stops.
- You smell gas. Don’t flip switches, don’t use anything that could spark, and don’t go looking for the leak. Get everyone out, then call your gas company or 911 once you’re outside.
- Your carbon monoxide alarm sounds. Get everyone out, pets included, and call 911 from outside. Don’t go back in until responders tell you it’s safe.
- The breaker trips again after one reset.
- You smell burning plastic or hot wiring. A light dusty smell the first time the heat runs each fall is normal and fades quickly, and our post on furnace smells covers the difference. A burning smell that lingers isn’t normal. Turn the furnace off at the switch and call.
- The furnace keeps short cycling, starting and stopping every few minutes, even with a clean filter.
- You’ve worked through every check above and the house is still cold.
What happens when a Budget technician comes out?
Tell us what you’ve already checked and any blink code you counted, so the technician doesn’t repeat your work. We’re based in St. Peters, and no-heat calls get top priority in a cold snap. Same-day visits are often available, and calling early gives you the best chance.
A residential visit has a $99 dispatch fee. That gets a technician to your door in a fully stocked truck to find the problem and give you a written repair estimate. Parts and labor for the repair are quoted separately, and nothing happens until you approve the price.
Our goal is always to repair, not replace. Many no-heat problems come down to one part, like a flame sensor or an ignitor. If a repair doesn’t make sense for the age of your furnace, the technician will say so and walk you through the options.
Still no heat?
If you’ve worked through the checks and the house is still cold, we’ll find out why. Our furnace repair page explains what a repair visit looks like. Call us at (636) 887-2800. If it’s after hours or you’d rather pick a time yourself, you can book online. Your neighbors called first.